Articles
All articles | Recent articles
Preparation of SiC Ceramics by Laminated Object Manufacturing and Pressureless Sintering
H. Zhong1,2, X. Yao1, Y. Zhu1, J. Zhang1, D. Jiang1, J. Chen1, Z. Chen1, X. Liu1, Z. Huang1
1 State Key Laboratory of High Performance Ceramics and Superfine Microstructures, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, China
2 Graduate University of the Chinese Academy of Sciences, Beijing 100049, China
received November 11, 2014, received in revised form January 24, 2015, accepted Febuary 20, 2015
Vol. 6, No. 2, Pages 133-140 DOI: 10.4416/JCST2014-00049
Abstract
In this paper, laminated object manufacturing (LOM) and pressureless sintering were applied to obtain complex-shaped SiC ceramic articles. The SiC green tapes measuring 0.15 mm in thickness used for LOM were prepared by means of organic-solvent-based tape casting. The influences of the binder content, plasticizer/binder ratio and solid loading on the tape properties were investigated and optimized. The binder removal and pressureless sintering processes were studied and optimized to obtain high-quality SiC samples. The relationships between the mechanical properties of the sintered body and the solid loading of green tape were studied. The final part with a relative density of 98.16 % can be obtained with a bending strength, hardness, toughness and elastic modulus of 402 ± 23 MPa, 19.86 ± 0.71 GPa, 3.32 ± 0.29 MPa m1/2 and 393 ± 41 GPa respectively. The result shows that LOM is suitable for the manufacture of SiC products with complex shape and beneficial for the design and small batch fabrication of complex-shaped ceramic parts.
Download Full Article (PDF)
Keywords
LOM, SiC, tape casting, binder removal, pressureless sintering, mechanical properties
References
1 Klosterman, D., Chartoff, R., Osborne, N.: Laminated object manufacturing, a new process for the direct manufacture of monolithic ceramics and continuous fiber CMCs, Ceram. Eng. Sci. Proc., 18, [12 – 16], 113 – 120, (1997).
2 Klosterman, D., Chartoff, R., Osborne, N., Graves, G., Lightman, A., Han, G.: Laminated object manufacturing (LOM) of advanced ceramics and composites, Proceedings of the 7th International Conference on Rapid Prototyping, (1997).
3 Zhang, Y., He, X., Han, J., Du, S., Zhang, J.: Al2O3 ceramics preparation by LOM, Int. J. Adv. Manuf. Tech., 17, 531 – 534, (2001).
4 Cui, X., Ouyang, S., Yu, Z.Y., Wang, C.A., Huang, Y.: A study on green tapes for LOM with water-based tape casting processing, Mater. Lett., 57, 1300 – 1304, (2003).
5 Zhang, Y.M., He, X.D., Han, J.C., Du, S.Y.: Ceramic green tape extrusion for laminated object manufacturing, Mater. Lett., 40, 275 – 279, (1999).
6 Gomes, C., Acchar, W., Birol, H.: Laminated object manufacturing of LZSA glass-ceramics, Rapid Prototyping J., 17, 424 – 428, (2011).
7 Gomes, C.M., Rambo, C.R., Greil, P.: Colloidal processing of glass-ceramics for laminated object manufacturing, J. Am. Ceram. Soc., 92, [6], 1186 – 1191, (2009).
8 Das, A., Madras, G., Dasgupta, N., Umarji, A.M.: Binder removal studies in ceramic thick shapes made by laminated object manufacturing, J. Eur. Ceram. Soc., 23, 1013 – 1017, (2003).
9 Bitterlich, B., Heinrich, J.G.: Processing, microstructure, and properties of laminated silicon nitride stacks, J. Am. Ceram. Soc., 88, 2713 – 2721, (2005).
10 Liu, S., Ye, F., Liu, L., Liu, Q.: Feasibility of preparing of silicon nitride ceramics components by aqueous tape casting in combination with laminated object manufacturing, Mater. Des., 66, 331 – 335, (2015).
11 Zeng, Y.P., Jiang, D.L., Greil, P.: Tape casting of aqueous Al2O3 slurries, J. Eur. Ceram. Soc., 20, 1691 – 1697, (2000).
12 Lv, Z.H., Zhang, T., Jiang, D.L., Zhang, J.X., Lin, X.L.: Aqueous tape casting process for SiC, Ceram. Int., 35, 1889 – 1895, (2009).
13 GutieÂrrez, C.A., Moreno, R.: Tape casting of non-aqueous silicon nitride slips, J. Eur. Ceram. Soc., 20, 1527 – 1537, (2000).
14 Zhang, J.X., Jiang, D.L., Lin, Q.L., Huang, Z.R.: Preparation of TiC ceramics through aqueous tape casting, Ceram. Int., 31, 475 – 480, (2005).
15 Nikzad, L., Mirhabibi, A.R., Vaezi, M.R., Javadpoor, J.: Tape casting of graphite in non-aqueous media, Mater. Des., 30, 346 – 352, (2009).
16 Schindler, K., Roosen, A.: Manufacture of 3D structure by cold low pressure lamination of ceramic green tapes, J. Eur. Ceram. Soc., 29, 899 – 904, (2009).
17 Piwonski, M.A., Roosen, A.: Low pressure lamination of ceramic green tapes by gluing at room temperature, J. Eur. Ceram. Soc., 19, 263 – 270, (1999).
18 Klosterman, D., Chartoff, R., Graves, G., Osborne, N.: Interfacial characteristics of composites fabricated by laminated object manufacturing, Compos. Part A., 29, 1165 – 1174, (1998).
19 Windsheimer, H., Travitzky, N., Hofenauer, A., Greil, P.: Laminated object manufacturing of preceramic-paper-derived Si-SiC composites, Adv. Mater., 19, 4515 – 4519, (2007).
Copyright
Göller Verlag GmbH