Articles
All articles | Recent articles
Influence of Heat Treatment of Amorphous Ti- and B-Containing SiC-Based Fiber in Air on Microstructure and Strength
Jiangxi Chen, Baojie Zhang, Danni Xu, Zhaoju Yu, Guomei He
Key Laboratory of High Performance Ceramic Fibers of Ministry of Education, Department of Materials Science and Engineering, College of Materials, Xiamen University, 361005, People's Republic of China.
received February 17, 2018, received in revised form March 28, 2018, accepted May 17, 2018
Vol. 9, No. 3, Pages 279-288 DOI: 10.4416/JCST2018-00014
Abstract
The oxidative behavior of amorphous Ti- and B-containing SiC-based fiber exposed to air flowing at 1100 – 1300 °C for 2 – 300 min was investigated. The results showed that the strength of the SiC-based fiber slightly decreased when the fibers were exposed to air for 2 min at 1000 – 1300 °C. When the exposure time was lengthened to 300 min or the exposure temperature was increased from 1000 °C to 1300 °C, the strength of the SiC-based fiber did not change significantly. The morphology studies with SEM revealed that defects on the fiber surface were generated at the beginning of oxidation, while they were healed by the growth of a smooth oxide layer during further oxidation. This study showed that the amorphous Ti- and B-containing Si-C-O phase displayed better oxidation resistance than the well-known amorphous Si-C-O phase. Thus, the resulting SiC-based fiber is able to maintain its amorphous structure and its strength in air up to 1300 °C.
Download Full Article (PDF)
Keywords
SiC fiber, oxidation, strength, microstructure, amorphous
References
1 Yajima, S., Hayashi, J., Omori, M., Okamura, K.: Development of a silicon carbide fibre with high tensile strength, Nature, 261, 683 – 685, (1976).
2 Yajima, S., Omori, M., Hayashi, J.: Continuous silicon carbide fiber of high tensile strength, Chem. Lett., 4, [9], 931 – 934, (1975).
3 Hasegawa, Y., Iimura, M., Yajima, S.: Synthesis of continuous silicon carbide fibre. Part 2. Conversion of polycarbosilane fibre into silicon carbide fibres, J. Mater. Sci., 15, 720 – 728, (1980).
4 Naslain, R.: Design, preparation and properties of non-oxide CMCs for application in engines and nuclear reactors: an overview, Compos. Sci. Technol., 64, 155 – 170, (2004).
5 Riedel, R., Mera, G., Hauser, R., Klonczynski, A.: Silicon-based polymer-derived ceramics: Synthesis properties and applications – a review, J. Ceram. Soc. Jpn., 114, [1330], 425 – 444, (2006).
6 Tressler, R.E.: Recent developments in fibers and interphases for high temperature ceramic matrix composites, Compos. Part A-Appl. S., 30, [4], 429 – 437, (1999).
7 Naslain, R.: Recent advances in the field of ceramic fibers and ceramic matrix composites, J. Phys. IV., 123, 3 – 17, (2005).
8 Naslain, R.R., Pailler, R.J.-F., Lamon, J.L.: Single- and multilayered interphases in SiC/SiC composites exposed to severe environmental conditions: An overview, Int. J. Appl. Ceram. Technol., 7, 263 – 275, (2010).
9 Huger, M., Souchard, S., Gault, C.: Oxidation of nicalon SiC fibres, J. Mater. Sci. Lett., 12, [6], 414 – 416, (1993).
10 Shimoo, T., Chen, H., Okamura, K.: Mechanisms of oxidation of Si-C-O fibers, J. Ceram. Soc. Jpn., 100, [1163], 929 – 935, (1992).
11 Wilson, M., Opila, E.: A review of SiC fiber oxidation with a new study of Hi-Nicalon SiC fiber oxidation, Adv. Eng. Mater., 18, [10], 1698 – 1709, (2016).
12 Zhu, Y.T., Taylor, S.T., Stout, M.G., Butt, D.P., Lowe, T.C.: Kinetics of thermal, passive oxidation of nicalon fibers, J. Am. Ceram. Soc., 81, [3], 655 – 660, (1998).
13 Naslain, R., Guette, A., Rebillat, F., Le Gallet, S., Lamouroux, F., Filipuzzi, L., Louchet, C.: Oxidation mechanisms and kinetics of SiC-matrix composites and their constituents, J. Mater. Sci., 39, [24], 7303 – 7316, (2004).
14 Shimoo, T., Morisada, Y., Okamura, K.: Oxidation behavior of Si-C-O fibers (Nicalon) under oxygen partial pressures from 102 to 105 Pa at 1773 k, J. Am. Ceram. Soc., 83, [12], 3049 – 3056, (2000).
15 He, G.W., Shibayama, T., Takahashi, H.: Microstructural evolution of Hi-NicalonTM SiC fibers annealed and crept in various oxygen partial pressure atmospheres, J. Mater. Sci., 35, [5], 1153 – 1164, (2000).
16 Shimoo, T., Toyoda, F., Okamura, K.: Oxidation kinetics of low-oxygen silicon carbide fiber, J. Mater. Sci., 35, 3301 – 3306, (2000).
17 Sha, J.J., Hinoki, T., Kohyama, A.: Microstructure and mechanical properties of Hi-Nicalon™ type S fibers annealed and crept in various oxygen partial pressures, Mater. Charact., 60, [8], 796 – 802, (2009).
18 Shimoo, T., Okamura, K., Morisada, Y.: Active-to-passive oxidation transition for polycarbosilane-derived silicon carbide fibers heated in Ar-O2 gas mixtures, J. Mater. Sci., 37, 1793 – 1800, (2002).
19 Wu, S.J., Cheng, L.F., Zhang, L.T., Xu, Y.D., Zhang, J., Mei, H.: Wet oxidation behaviors of Hi-Nicalon fibers, Appl. Surf. Sci., 253, 1447 – 1450, (2006).
20 Kim, H.E., Moorhead, A.J.: Strength of nicalon silicon carbide fibers exposed to high-temperature gaseous environments, J. Am. Ceram. Soc., 74, [3], 666 – 669, (1991).
21 Bodet, R., Jia, N., Tressler, R.E.: Microstructural instability and the resultant strength of Si-C-O (Nicalon) and Si-N-C-O (HPZ) fibers, J. Eur. Ceram. Soc., 16, 653 – 664, (1996).
22 Zima, T.M., Baklanova, N.I., Titov, A.T.: The behavior of the oxide-coated Nicalon™ fibers exposed to air at 1000 °C, J. Eur. Ceram. Soc., 25, 1943 – 1952, (2005).
23 Cinibulk, M.K., Parthasarathy, T.A.: Characterization of oxidized polymer-derived SiBCN fibers, J. Am. Ceram. Soc., 84, [10], 2197 – 2202, (2001).
24 Takeda, M., Urano, A., Sakamoto, J.I., Imai, Y.: Microstructure and oxidative degradation behavior of silicon carbide fiber Hi-Nicalon type S, J. Nucl. Mater., 258 – 263, 1594 – 1599, (1998).
25 Shimoo, T., Morisada, Y., Okamura, K.: Oxidation behavior of Si-M-C-O fibers under wide range of oxygen partial pressures, J. Mater. Sci., 37, [20], 4361 – 4368, (2002).
26 Mah, T., Hecht, N.L., Mc Cullum, D.E., Hoenigman, J.R., Kim, H.M., Katz, A.P., Lipsitt, H.A.: Thermal stability of SiC fibres (Nicalon®), J. Mater. Sci., 19, [4], 1191 – 1201, (1984).
27 Simon, G., Bunsell, A.R.: Creep behaviour and structural characterization at high temperatures of nicalon SiC fibres, J. Mater. Sci., 19, [11], 3658 – 3670, (1984).
28 Bunsell, A.R., Piant, A.: A review of the development of three generations of small diameter silicon carbide fibres, J. Mater. Sci., 41, [3], 823 – 839, (2006).
29 Bunsell, A.R., Berger, M.H.: Fine diameter ceramic fibres, J. Eur. Ceram. Soc., 20, [13], 2249 – 2260, (2000).
30 Wang, B.W., Li, H.M., Xu, L.M., Chen, J.X., He, G.M.: Fine-diameter microwave-absorbing SiC-based fiber, RSC Adv., 7, 12126 – 12132, (2017).
31 He, G.M., Zhang, B.J., Wang, B.W., Xu, D.N., Li, S.W., Yu, Z.J., Chen, J.X.: Amorphous fine-diameter SiC-based fiber from a boron-modified polytitanocarbosilane precursor, J. Eur. Ceram. Soc., 38, 1079 – 1086, (2018).
32 Liu, X.F., Zhang, L.T., Yin, X.W., Ye, F., Liu, Y.S., Cheng, L.F.: The microstructure and electromagnetic wave absorption properties of near-stoichiometric SiC fibre, Ceram. Int., 43, [3], 3267 – 3273, (2017).
33 Ye, F., Zhang, L.T., Yin, X.W., Liu, Y.S., Cheng, L.F.: Dielectric and electromagnetic wave absorbing properties of two types of SiC fibres with different compositions, J. Mater. Sci. Technol., 29, [1], 55 – 58, (2013).
34 Hou, Y., Cheng, L.F., Zhang, Y.N., Yang, Y., Deng, C.R., Yang, Z.H., Chen, Q., Wang, P., Zheng, L.X.: Electrospinning of Fe/SiC hybrid fibers for highly efficient microwave absorption, Acs Appl. Mater. Interfaces., 9, [8], 7265 – 7271, (2017).
35 Yajima, S., Hasegawa, Y., Hayashi, J., Iimura, M.: Synthesis of continuous silicon carbide fibre with high tensile strength and high Young's modulus. Part 1. Synthesis of polycarbosilane as precursor, J. Mater. Sci., 13, 2569 – 2576, (1978).
36 "Tensile strength and Young's modulus for high-modulus single-filament materials," ASTM Designation D-3379 – 75. 1983 Annual Book of ASTM Standards, Part 15. American Society for Testing and Materials, Philadelphia, PA.
37 Yao, R.Q., Feng, Z.D., Chen, L.F., Zhang, Y., Zhang, B.J.: Oxidation behavior of Hi-Nicalon SiC monofilament fibres in air and O2-H2O-Ar atmospheres, Corros. Sci., 57, [2], 182 – 191, (2012).
38 Takeda, M., Urano, A., Sakamoto, J.I., Imai, Y.: Microstructure and oxidation behavior of silicon carbide fibers derived from polycarbosilane, J. Am. Ceram. Soc., 83, [5], 1171 – 1176, (2000).
39 Smith, R.L., Mecholsky, Jr, J.J.: Application of atomic force microscopy in determining the fractal dimension of the mirror, mist, and hackle region of silica glass, Mater. Charact., 62, [5], 457 – 462, (2011).
40 Mecholsky, J.J., Rice, R.W., Freiman, S.W.: Prediction of fracture energy and flaw size in glasses from measurements of mirror size, J. Am. Ceram. Soc., 57, [10], 440 – 443, (1974).
41 Youngblood, G.E., Lewinsohn, C., Jones, R.H., Kohyama, A.: Tensile strength and fracture surface characterization of Hi-NicalonTM SiC fibers, J. Nucl. Mater., 289, [1], 1 – 9, (2001).
42 Huo, C.X., Guo, L.J., Li, Y.Y., Wang, C.C., Feng, L., Liu, N.K., Zhang, Y.L., Dong, K.Y., Song, Q.: Effect of co-deposited SiC nanowires and carbon nanotubes on oxidation resistance for SiC-coated C/C composites, Ceram. Int., 43, [2], 1722 – 1730, (2017).
43 Zhu, Y.T., Taylor, S.T., Stout, M.G., Butt, D.P., Lowe, T.C.: Kinetics of thermal, passive oxidation of nicalon fibers, J. Am. Ceram. Soc., 81, [3], 655 – 660, (2010).
44 Shimoo, T., Toyoda, F., Okamura, K.: Thermal stability of low-oxygen silicon carbide fiber (Hi-Nicalon) subjected to selected oxidation treatment, J. Am. Ceram. Soc., 83, [6], 1450 – 1456, (2000).
45 Bunsell, A.R., Piant, A.: A review of the development of three generations of small diameter silicon carbide fibres, J. Mater. Sci., 41, [3], 823 – 839, (2006).
46 Kister, G., Harris, B.: Tensile properties of heat-treated nicalon and Hi-Nicalon fibres, Compos. Part A-Appl. S., 33, [3], 435 – 438, (2002).
47 Bansal, N.P.: Mechanical properties of Hi-Nicalon fiber-reinforced celsian composites after high-temperature exposures in air, J. Eur. Ceram. Soc., 29, 525 – 535, (2009).
48 Sha, J.J., Hinoki, T., Kohyama, A.: Thermal and mechanical stabilities of Hi-Nicalon SiC fiber under annealing and creep in various oxygen partial pressures, Corros. Sci., 50, [11], 3132 – 3138, (2008).
49 Wang, J.J., Zhang, L.T., Zeng, Q.F., Vignoles, G.L., Cheng, L.F., Guette, A.: The rate-limiting step in the thermal oxidation of silicon carbide, Scripta Mater., 62, [9], 654 – 657, (2010).
Copyright
Göller Verlag GmbH