Articles
All articles | Recent articles
Thermoplastic Forming as an Alternative Shaping Process for Near-Net-Shape Production of C-SiSiC Ceramics via Liquid Silicon Infiltration (LSI) Process
S. Weber1, F. Sommer2, F. Kern2, R. Gadow2, H. Voggenreiter1, D. Koch1
1 Institute of Structures and Design, Dep. Ceramic Composites and Structures, German Aerospace Center (DLR), Pfaffenwaldring 38 – 40, D-70569 Stuttgart, Germany
2 Institute for Manufacturing Technologies of Ceramic Components and Composites, University of Stuttgart, Allmandring 7b, D-70569 Stuttgart, Germany
received March 12, 2014, received in revised form May 7, 2014, accepted May 25, 2014
Vol. 5, No. 3, Pages 223-236 DOI: 10.4416/JCST2014-00011
Abstract
The present study demonstrated the feasibility of producing carbon-based green bodies by means of extrusion, pyrolysis and subsequent conversion to C-SiSiC ceramics according to the LSI process. A thermoplastic binder system was used for the development of feedstocks that differ from conventional duroplastic binder systems as these would have created difficulties during processing owing to their curing behavior. Activated carbon, carbon fibers and semi-coke were used as fillers and a source of a sufficiently stable carbon backbone in the carbonized intermediate. Special attention was paid to the characterization and quantification of material behavior at the water debinding step as well as at thermal treatment during pyrolysis. Porosity and microstructural characteristics of carbon bodies and subsequent C-SiSiC microstructure after Si-infiltration were investigated by means of scanning electron microscopy and porosity measurements. The feasibility of producing carbon-based extrusion feedstocks with high homogeneity and flowability which can be converted into SiC by means of LSI shows that the concept may be applied to production of near-net-shape C-SiSiC components by means of thermoplastic injection molding.
Download Full Article (PDF)
Keywords
Extrusion, injection molding, SiC, porosity, feedstock system
References
1 Kollenberg, W.; Technische Keramik, Vulkan-Verlag GmbH, Essen, (2004) (in German)
2 Liu, G., Li, J., Shan, Y., Xu, J.: Highly dense β-SiC ceramics with submicron grains prepared by sintering of nanocrystalline powders, Scripta Mater., 67, 416 – 41, (2012).
3 Gadow, R.: The siliconization of carbon, (in German), Dissertation, University of Karlsruhe, (1986).
4 Wang, Y., Tan, S.,Jiang, D.: The fabrication of reaction-formed silicon carbide with controlled microstructure by infiltrating a pure carbon preform with molten Si, Ceram. Int., (2004)
5 Wang, Y., Tan, S., Jiang, D.: The effect of porous carbon preform and the infiltration process on the properties of reaction-formed SiC, Carbon, 42, 1833 – 1839, (2004).
6 Singh, M., Behrendt, D.: Reactive melt infiltration of silicon-molybdenum alloys into microporous carbon preforms, Mater. Sci. Eng. A, 194, 193 – 200, 1995
7 Kumar, S., Kumar, A., Devi, R., Shukla, A., Gupta, A.: Capillary infiltration studies of liquids into 3D-stitched C-C preforms: part B: kinetics of silicon infiltration, J. Eur. Ceram. Soc., 29, 2651 – 2657, (2009).
8 Kumar, S., Kumar, A., Shukla, A., Gupta, A., Devi, R.: Capillary infiltration studies of liquids into 3D-stitched C-C preforms: part A: internal pore characterization by solvent infiltration, mercury porosimetry, and permeability studies, J. Eur. Ceram. Soc., 29, 2643 – 2650, (2009).
9 Voytovych, R., Israel, R., Calderon, N., Hodaj, F., Eustathopoulos, N.: Reactivity between liquid si or si alloys and graphite, J. Eur. Ceram. Soc., 32, 3825 – 3835, (2012).
10 Magnant, J., Maillé, L., Pailler, R., Ichard, J.-C., Guette, A., Rebillat, F., Philippe, E.: Carbon fiber/reaction-bonded carbide matrix for composite materials – manufacture and characterization, J. Eur. Ceram. Soc., 32, 4497 – 4505, (2012).
11 Margiotta, J.C., Zhang, D., Nagle, D.C., Feeser, C.E.: Formation of dense silicon carbide by liquid silicon infiltration of carbon with engineered structure, J. Mater. Res., 23, 1237 – 1248, (2008).
12 Margiotta, J.C. et al.: Formation of dense silicon carbide by liquid silicon infiltration of carbon with engineered structure, Cambridge Journal, (2004).
13 Nelson, E.S., Colella, P.: Parametric study of reactive melt infiltration, Proceedings of the 1999 International Mechanical Engineering Congress and Exposition, (1999).
14 Xu, S., Qiao, G., Li, D., Yang, H., Liu, Y., Lu, T.: Reaction forming of silicon carbide ceramic using phenolic resin derived porous carbon preform, J. Eur. Ceram. Soc., 29, 2395 – 2402, (2009).
15 Li, S., Zhang, Y., Han, J., Zhou, Y.; Effect of carbon particle and carbon fiber on the microstructure and mechanical properties of short fiber reinforced reaction bonded silicon carbide composite, J. Eur. Ceram. Soc., (2012).
16 Li, S., Zhang, Y., Han, J., Zhou, Y.: Random chopped fibers in reaction bonded SiC composite: morphology, etching and reinforcing properties, Mater. Sci. Eng. A, 551, 104 – 10, (2012).
17 Weber, S. et al.: Microstructures and physical properties of biomorphic SiSiC ceramics manufactured via LSI-technique. Proceedings of the 36th International Conference and Expo on Advanced Ceramics and Composites, San Diego, (2012).
18 Weber, S. et al..: Activated carbon based compound systems for the manufacture of complex shaped SiSiC structures, (in German), Deutsche Keramische Gesellschaft, Arbeitskreis "Kohlenstoff" (AKK), (2012).
19 Lara, A., Muñoz, A., Castillo-Rodríguez, M., Domínguez-Rodríguez, A.: High-temperature compressive creep of spark-plasma sintered additive-free polycrystalline β-SiC, J. Eur. Ceram. Soc., 32, 3445 – 3451, (2012).
20 Jang, B.K., Sakka, Y.: Influence of microstructure on the thermophysical properties of sintered SiC ceramics, J. Alloy. Compd., 463, 493 – 497, (2008).
21 Malinge, A., Coupé, A., Petitcorps, Y.L., Pailler, R.: Pressureless sintering of beta silicon carbide nanoparticles, J. Eur. Ceram. Soc., (2012)
22 Petutschnigg, A.: Development of a shaping process for wood-based green bodies for the production of biogenic SiC ceramics, (in German), Federal Ministry for Transport, Innovation and Technology, 39/2012, 2012
23 Kern, F., Gadow, R.; Extrusion and injection molding of ceramic micro and nanocomposites, Inter. J. Mater. Forming, 01/2009; 2:609 – 612, (2009).
24 Kern, F., Gadow, R.: Model assisted optimization of debindering and sintering processes in ceramic injection molding, Stuttgarter Kunstoffkolloqium, (2011).
Copyright
Göller Verlag GmbH