Articles
All articles | Recent articles
Influence of Sintering Parameters on the Structure of Alumina Tubular Membranes Obtained by Freeze-Casting
P. Cristh Fonseca Alves1, D. Guimarães da Silva1, D. Cordeiro Leite Vasconcelos1, W.L. Vasconcelos1, J. Ferreira do Nascimento2, D. Carrijo de Melo2, L. dos Santos Pereira2
1 Department of Metallurgical and Materials Engineering, Federal University of Minas Gerais - UFMG, Avenida Presidente Antônio Carlos, 6627, Campus UFMG, Escola de Engenharia, bloco 2, sala 2233, Belo Horizonte, MG, CEP: 31270 – 901, Brazil.
2 Petrobras/CENPES, Avenida Horácio Macedo 950, Cidade Universitária, Ilha do Fundão, Rio de Janeiro, RJ, CEP: 21941 – 915, Brazil.
received July 3, 2023, received in revised form September 11, 2023, accepted September 25, 2023
Vol. 14, No. 2, Pages 89-98 DOI: 10.4416/JCST2023-00009
Abstract
This study compares for the first time the influence of different sintering routes on the structure of alumina samples prepared with the freeze-casting technique. Two-stage and fast sintering routes were compared with the conventional sintering route, and the sintering program proved to be crucial in controlling the microstructure of alumina ceramics. The results suggest that the alumina porosity and particle size are highly dependent on the sintering route. It was observed that the two-step sintering route is more efficient in controlling the particle growth of alumina (0.8 µm) when compared to the conventional (1.2 µm) and fast (0.9 µm) sintering routes. Regarding the mechanical properties, it was observed that an improvement in flexural strength was achieved when the two-stage sintering program (6.15 MPa) was used, which is associated with its microstructural refinement.
Download Full Article (PDF)
Keywords
Freeze-casting, alumina tubes, sintering, membranes
References
1 Deville, S.: Freeze-casting of porous ceramics: A review of current achievements and issues, Adv. Eng. Mater., 10, [3], 155 – 169, (2008) doi: https://dx.doi.org/10.1002/adem.200700270
2 Pagano, E., Chinelatto, A.S.A., Chinelatto, A.L.: Freeze casting process for the generation of graded porosity in Al2O3 ceramics, Ceramica, 66, [377], 65 – 73, (2020). doi: https://doi.org/10.1590/0366 – 69132020663772690.
3 Barbosa, T.L.A., Silva, F.M.N., Barbosa, A.S., Lima, E.G., Rodrigues, M.G.F.: Synthesis and application of a composite NaA zeolite/gamma-alumina membrane for oil-water separation process, Ceramica, 66, 137 – 144 (2020). doi: https://dx.doi.org/10.1590/0366 – 69132020663782820.
4 Hyun, S.H., Kim, G.T.: Synthesis of ceramic microfiltration membranes for oil/water separation, Sep. Sci. Technol., 32, [18], 2927 – 2943, (1997). doi: https://doi.org/10.1080/01496399708000788.
5 Kabir, S.M., Minhaj, I.T., Ashrafi, A.E., Hossain, M.M.: Influence of sintering routes on the structure and indentation hardness of nano α-Al2O3 particles, IJAENT, 9, 2347 – 6389, (2014).
6 Wu, T., Wang, B., Lu, Z., Zhou, R., Chen, X.: Alumina-supported AlPO-18 membranes for CO2/CH4 separation, J. Membr. Sci., 471, 338 – 346, (2014). doi: https://dx.doi.org/10.1016/j.memsci.2014.08.035.
7 Liu, R., Xu, T., Wang, C.: A review of fabrication strategies and applications of porous ceramics prepared by freeze-casting method, Ceram. Int., 42, 2907 – 2925, (2016). doi: https://dx.doi.org/10.1016/j.ceramint.2015.10.148.
8 German, R.M.: Thermodynamics of sintering, San Diego State University, In book: Sintering of advanced materials, Woodhead Publishing, 3 – 32, 2010.
9 Rahaman, M.N.: Ceramic Processing and Sintering, Second Edition, New York, CRC Press, 550, 2017.
10 Callister, W.D. Jr., Rethwisch, D.G.: Wiley, Salt Lake City, Eighth edition: Materials Science and Engineering, 2010.
11 Awotunde, M.A., Adegbenjo, A.O., Obadele, B.A., Okoro, M., Shongwe, B.M., Olubambi, P.A.: Influence of sintering methods on the mechanical properties of aluminium nanocomposites reinforced with carbonaceous compounds: A review, J. Mater. Res. Technol., 8, [2], 2432 – 2449, (2019). doi: https://doi.org/10.1016/j.jmrt.2019.01.026.
12 Bodišová, K., Galusek, D., Švančárek, P., Pouchlý, V., Maca, K.: Grain growth suppression in alumina via doping and two-step sintering, Ceram. Int., 41, [9], 11975 – 11983, (2015). doi: https://doi.org/10.1016/j.ceramint.2015.05.162.
13 Chen, I.W., Wang, X.H.: Sintering dense nanocrystalline ceramics without final-stage grain growth, Nature, 9, 168 – 171, (2000). doi: https://doi.org/10.1038/35004548.
14 Bodišová, K., Sajgalik, P., Galusek, D., Svancarek, P.: Two-stage sintering of alumina with submicrometer grain size, J. Am. Ceram. Soc., 90, 330 – 332, (2007). doi: https://doi.org/10.1111/j.1551 – 2916.2006.01408.x.
15 Galusek, D., Ghillányová, K., Sedláček, J., Kozánková, J., Šajgalík, P.: The influence of additives on microstrucutre of sub-micron alumina ceramics prepared by two-stage sintering, J. Eur. Ceram., 32, 1965 – 1970, (2012). doi: https://doi.org/10.1016/j.jeurceramsoc.2011.11.038
16 Prajzler, V., Salamon, D., Maca, K.: Pressure-less rapid rate sintering of pre-sintered alumina and zirconia ceramics, Ceram. Int., 44, 10840 – 10846, (2018). doi: https://doi.org/10.1016/j.ceramint.2018.03.132.
17 Kang, S.L.: What we should consider for full densification when sintering, Materials, 13, (2020). doi: https://doi.org/10.3390/ma13163578.
18 Esposito, V., Traversa, E.: Design of electroceramics for solid oxides fuel cell applications: playing with ceria, J. Am. Ceram., 91, 1037 – 1051, (2008).
19 Isobe, T., Ooyama, A., Shimizu, M., Nakajima, A.: Pore size control of Al2O3 ceramics using two-step sintering, Ceram. Int., 38, 787 – 793, (2012). doi: https://doi.org/10.1016/j.ceramint.2011.08.005.
20 Lóh, N.J., Simão, L., Jiusti, J., Arcaro, S., Raupp-pereira, F., De Noni Jr., A., Montedo, O.R.K.: Densified alumina obtained by two-step sintering: impact of the microstructure on mechanical properties, Ceram. Int., 46, 12740 – 12743, (2020). doi: https://doi.org/10.1016/j.ceramint.2020.02.042.
21 Lóh, N.J., Simão, L., Faller, C.A., De Noni Jr, A., Montedo, O.R.K.: A review of two-step sintering for ceramics, Ceram. Int., 42, 12556 – 12572, (2016). doi: https://dx.doi.org/10.1016/j.ceramint.2016.05.065
22 Xu, T., Wang, C.-A.: Effect of two-step sintering on micro-honeycomb BaTiO3 ceramics prepared by freeze-casting process, J. Eur. Ceram., 36, 2647 – 2652, (2016). doi: https://doi.org/10.1016/j.jeurceramsoc.2016.03.032.
23 A.S.T.M. B962 – 17, Standard test methods for density of compacted or sintered powder metallurgy (PM) products using Archimedes' principle, 2017.
24 A.S.T.M. C20 – 00, Standard test methods for apparent porosity, water absorption, apparent specific gravity, and bulk density of burned refractory brick and shapes by boiling water, 2015.
25 Wit, P., Daalen, F.S., Benes, N.E.: The mechanical strength of a ceramic porous hollow fiber, J. Membr. Sci., 524, 721 – 728, (2017). doi: https://dx.doi.org/10.1016/j.memsci.2016.11.047.
26 Coble, R.L.: Sintering crystalline solids. I. Intermediate and final state diffusion models. J. Appl. Phys., 32, 787 – 792, (1961). doi: https://dx.doi.org/10.1063/1.1736107.
27 Silva, L.O., Vasconcelos, D.C.L., Nunes, E.H.M., Caldeira, L., Costa, V.C., Musse, A., Hatimondi, S.A., Nascimento, J.F., Grava, W., Vasconcelos, W.L.: Processing, structural characterization and performance of alumina supports used in ceramic membranes, Ceram. Int., 38, 1943 – 1949, (2012). doi: https://doi.org/10.1016/j.ceramint.2011.10.025.
28 Pouchly, V., Maca, K.: Sintering kinetic window for yttria-stabilized cubic zirconia vaclav, J. Eur. Ceram., 36, 2931 – 2936, (2016). doi: https://dx.doi.org/10.1016/j.jeurceramsoc.2015.12.044.
29 Khan, U.A., Hussain, A., Shah, M., Shuaib, M., Qayyum, F.: Investigation of mechanical properties based on grain growth and microstructure evolution of alumina ceramics during two step sintering process. IOP Conf., 146, (2016). doi: https://dx.doi.org/10.1088/1757 – 899X/146/1/012046.
30 Pan, Y., Li H., Liu, Y., Liu, Y., Hu, K., Wang, N., Lu, Z., Liang, J., He, S.: Effect of holding time during sintering on microstructure and properties of 3D printed alumina ceramics, Front. Mater., 7, [54], (2020). doi: https://dx.doi.org/10.3389/fmats.2020.00054.
31 Biesuz, M., Grasso, S., Sglavo, V.M.: What's new in ceramics sintering? A short report on the latest trends and future prospects, Curr. Opin. Solid State Mater. Sci., 24, [5], 100868, (2020). doi: https://doi.org/10.1016/j.cossms.2020.100868
Copyright
Göller Verlag GmbH